Mazda 3 since 2003
	1. Operation and maintenance of the car
	2. Engine
		2.1. General description of new engines of the L8, LF and L3 models
		2.2. Mechanical part of engines
			2.2.1. Engines of the L8 and LF models
			2.2.2. Verification of the contents of CO/CH in the fulfilled gases
			2.2.3. Measurement of a compression in engine cylinders
			2.2.4. Check of a belt of the drive of auxiliary units
			2.2.5. General information and safety measures at removal of the power unit
			2.2.6. Removal of sealant
			2.2.7. Removal and installation of the power unit
			2.2.8. Check of the executive mechanism of change of phases of gas distribution (L3)
			2.2.9. Removal and installation of the executive mechanism of change of phases of gas distribution (L3)
			2.2.10. Gas distribution mechanism drive chain
			2.2.11. Removal and installation of the operating oil valve (OCV) (L3)
			2.2.12. Check of the operating oil valve (OCV) (L3)
			2.2.13. Check of operation of the spool-type valve (OCV) (L3)
			2.2.14. The general repair operations on the power unit
				2.2.14.1. Dismantling of a head of the block of cylinders (beginning)
				2.2.14.2. Dismantling of a head of the block of cylinders (termination)
				2.2.14.3. Dismantling of the block of cylinders (beginning)
				2.2.14.4. Removal and installation of a back epiploon of a bent shaft
				2.2.14.5. Dismantling of the block of cylinders (termination)
			2.2.15. Check of a head of the block of cylinders
			2.2.16. Assembly of the block of cylinders (beginning)
			2.2.17. Assembly of the block of cylinders (termination)
			2.2.18. Assembly of a head of the block of cylinders
			2.2.19. Assembly of the drive of the mechanism of gas distribution
		2.3. Appendix 1
		2.4. Appendix 2
		2.5. Appendix 3
		2.6. The Z6 engine – a mechanical part
		2.7. Lubrication system
		2.8. Cooling system
		2.9. System of an admission
		2.10. Fuel system
		2.11. System of production of the fulfilled gases and system of decrease in toxicity
		2.12. System of ignition
		2.13. Control system
		2.14. Tables
	3. Transmission
	4. Running gear
	5. Steering mechanism
	6. Brake system
	7. Onboard electric equipment
	8. Body

2-2-14-4-snyatie-i-ustanovka-zadnego-salnika-kolenchatogo-vala.html

2.2.14.4. Removal and installation of a back epiploon of a bent shaft

Fig. 2.130. Removal of a back epiploon of a bent shaft: 1 – bolts; 2 – epiploon

Turn off six bolts of fastening of a back epiploon and remove an epiploon (fig. 2.130).

Fig. 2.131. Places of putting sealant

Apply kremniyevoorganichesky sealant on the interfaced surfaces in the place shown in the figure 2.131. Diameter of a point of drawing 0,4–0,6 mm.

Apply pure engine oil on a working edge of a new epiploon.

Fig. 2.132. Scheme of installation of a back epiploon of a bent shaft: 1 – bent shaft; 2 – back epiploon; 3 – device for installation; 4 – block of cylinders

Establish and press a back epiploon, using the device for installation of a detail, as shown in the figure 2.132.

Fig. 2.133. Order of tightening of bolts of fastening of a back epiploon of a bent shaft

Tighten bolts of fastening of a back epiploon in the order specified in the figure 2.133, the moment of an inhaling of 8,0-11,5 N · m.

"previous page
2.2.14.3. Dismantling of the block of cylinders (beginning)

following page"
2.2.14.5. Dismantling of the block of cylinders (termination)