Mazda 3 since 2003
1. Operation and maintenance of the car
2. Engine
3. Transmission
3.1. Coupling
3.2. Mechanical transmission
3.3. Automatic transmission
3.3.1. General information
3.3.2. Design and operation of the mechanism of transmission
3.3.3. System of electronic control (RSM)
3.3.4. Mechanism of switching of the automatic transmission
3.3.4.1. Principle of operation of the mechanism of switching of the automatic transmission
3.3.4.2. Switching blocking check
3.3.4.3. Check of blocking of the ignition key
3.3.4.4. Check of a cable of blocking
3.3.4.5. Check of the lever of the selector
3.3.4.6. Adjustment of a cable of the choice of transfer
3.3.4.7. Adjustment of the switch of range of the transmission
3.3.4.8. Removal and installation of the lever of the selector
3.3.4.9. Installation of a cable of blocking
3.4. Driving mechanism
3.5. Tables
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
 








d925ae9b




3-3-4-8-snyatie-i-ustanovka-rychaga-selektora.html

3.3.4.8. Removal and installation of the lever of the selector

Fig. 3.88. Mechanism of switching of the automatic transmission: 1 – facing of a steering column (with the mechanism of blocking of a key); 2 – a clip (with the mechanism of blocking of a key); 3 – a clip (with the mechanism of blocking of a key); 4 – a blocking cable (with the mechanism of blocking of a key); 5 – transfer choice cable; 6 – gate selector lever


The mechanism of switching of the automatic transmission is shown in fig. 3.88.
Disconnect a negative wire of the rechargeable battery.
Remove the rechargeable battery and its tray.
Remove the air filter.
Remove the console.
Remove the dashboard.
Remove the module of management of the control system of stability.

Fig. 3.89. Removal of the control unit of climatic installation: 1 cables of control of the air gate; 2 – block of climatic installation


Remove the control unit of climatic installation (fig. 3.89).
Remove a back air duct.
Remove facing of a steering column.
Disconnect clips and remove a cable of blocking and a cable of the choice of transfer.

NOTE
Carry out installation in the order specified in the figure 3.88. Separate procedures for removal and installation are described in this section below.


Fig. 3.90. Scheme of installation of a cable of the choice of transfer


To establish a cable of the choice of transfer it is necessary to establish at first it on an arm, as shown in the figure 3.90.
Before replacement of a cable of the choice of transfer check that the lever of the selector is in situation P.

Fig. 3.91. Blocking of a clamp of a cable of the choice of transfer (from the selector lever)


Block a transfer choice cable clamp (from the selector lever) in the order shown in the figure 3.91.

Fig. 3.92. Check of a shaft of manual switching


Check that the shaft of manual switching is in situation P (fig. 3.92).

ATTENTION
At installation of a cable of the choice of transfer you hold it directly. Bending of a cable of the choice of transfer, as shown in the figure 3.92, will lead to damage of a cable, it can become the reason of weakening of a cable when switching.

Fig. 3.93. The correct installation of the lever of the selector on the lever of a shaft of manual switching



NOTE
Install the selector lever on the lever of a shaft of manual switching so that the spring of a tip of a cable of the choice of transfer was turned towards a forward part of the car (fig. 3.93).

Install the selector lever on the lever of a shaft of manual switching so that the cable of the choice of transfer was not loaded.
Make sure that the end of the lever of a shaft of manual switching leaves a transfer choice cable tip.
Establish a cable of the choice of transfer to an arm.

"previous page
3.3.4.7. Adjustment of the switch of range of the transmission
following page"
3.3.4.9. Installation of a cable of blocking