Removal. Mazda 3 (since 2003 release)
Mazda 3 since 2003
1. Operation and maintenance of the car
2. Engine
2.1. General description of new engines of the L8, LF and L3 models
2.2. Mechanical part of engines
2.3. Appendix 1
2.4. Appendix 2
2.5. Appendix 3
2.6. The Z6 engine – a mechanical part
2.6.1. Check of a belt of the drive of auxiliary units
2.6.2. Check of thermal gaps in the mechanism of the drive of valves
2.6.3. Check of a compression
2.6.4. Removal and installation of a chain of the drive of the mechanism of gas distribution
2.6.5. Replacement of laying of the block of cylinders
2.6.6. Replacement of a forward epiploon of a bent shaft
2.6.7. Replacement of a back epiploon of a bent shaft
2.6.8. Removal and installation of the engine
2.6.8.1. Removal
2.6.8.2. Removal of the socket of the main block of safety locks
2.6.8.3. Removal of support of the engine No. 3 and No. 4
2.6.8.4. Removal of a support of the engine and No. 4
2.6.8.5. Installation of a support of the engine and No. 4
2.6.8.6. Installation of a support of the engine No. 3
2.7. Lubrication system
2.8. Cooling system
2.9. System of an admission
2.10. Fuel system
2.11. System of production of the fulfilled gases and system of decrease in toxicity
2.12. System of ignition
2.13. Control system
2.14. Tables
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
 








2-6-8-1-snyatie.html

2.6.8.1. Removal

NOTE
Removal and installation of the engine and transmission in the block with the main transfer is carried out from below the car.

Remove the following elements:
– cover of the rechargeable battery, accumulator box, bracket of fastening of the rechargeable battery, rechargeable battery and platform of the rechargeable battery;
– forward wheels;
– lower cover and mudguards;
– air duct, air hose and knot of the air filter;
– rope of an accelerator and arm;
– driving belt.
Merge the following liquids:
– working liquid for the automatic transmission or transmission oil in the block with the main transfer;
– cooling liquid of the engine;
– working liquid of the hydraulic booster of steering.
Disconnect a purge valve hose.
Disconnect a returnable hose of the amplifier of steering from the oil pump of the amplifier of steering.
Disconnect the pressure head pipeline of the amplifier of steering from the steering mechanism.
Disconnect a returnable hose of the amplifier of steering from a tank of the hydraulic booster of steering.
Remove the following elements:
– lobby cross-piece, forward stabilizer, lower lever, steering mechanism and element of a support of the engine No. 1;
– power shaft;
– a tank of the hydraulic booster of steering with a hose;
– a broad tank of the cooling system with a hose;
– cooling system fan knot;
– the worker's hose liquid for the automatic transmission, a cable of the choice of transfer and a plait of wires (model with the automatic transmission);
– a cable of the choice of transfer and a cable of the drive of switching (model with the mechanical transmission);
– the working cylinder of coupling with a tube (models with the mechanical transmission);
– earth (engine No. 3 support);
– the compressor of the air conditioning system with tubes.

NOTE
Fix the compressor of the air conditioning system by a wire or a rope so that it did not prevent work.

Disconnect the following elements:
– hose of the vacuum amplifier of brakes;
– fuel supply hose;
– heater radiator hose;
– top and lower hose of a radiator;
– main muffler.

ATTENTION
Do not tighten a bolt of fastening of a support No. 1 of the engine before installation of a support of the engine No. 3.

Check and adjust if necessary the following:
– angles of installation of forward wheels
– pulley and belt.
– leak of engine oil, cooling liquid of the engine, working liquid for the automatic transmission, oil of the mechanical transmission and fuel.
– installation of a corner of an advancing of ignition and idling rotation frequency. Check the size CO, CH.
– operation of the service equipment with the drive from the engine.

NOTE
If on the car the engine after capital repairs is installed, execute a trial trip, and be convinced that everything works normally.

"previous page
2.6.8. Removal and installation of the engine
following page"
2.6.8.2. Removal of the socket of the main block of safety locks




d925ae9b